ZJ Composites fibreglass walkway mesh

Material: low carbon steel wire

The positive and negative twisting of barbed rope is less than 3 cents per meter, and the corresponding 12 hot-dip galvanized barbed rope is 50 cents per meter. No matter from the service life, tensile strength, rust prevention effect is no worse than 12 iron wire

There is still some demand for galvanized barbed rope by daily residents, but often the quantity is not particularly much. If the barbed rope factory delivers goods, then the extra freight may be higher than the price of the customer to buy the barbed rope in the market. The thorn rope factory sells to customers who buy in large quantities. There is a lot of demand for it, and it also hopes to find a manufacturer to purchase. Customer procurement problems can be much more complete introduction in the thorn rope factory, but also let customers more at ease.

Traditional wire mesh is crisscross woven into the wire, with the development of the economy, the rapid rise of all walks of life, the use of traditional wire mesh limitations gradually exposed, such as: aquaculture, to the chicken circle a cage can not be too dense, the wire can not be too thick, woven up the net wire once the mesh is too large net surface will become soft.

For single-layer wound non-rotating wire rope, it is necessary to strictly abide by the above principles, otherwise it is easy to cause permanent deformation of wire rope structure; In the case of multilayer winding, the rotation of the rope is determined by the orientation of the reel’s rope groove to lay the foundation for the next layer. The friction between the wire rope and the extrusion pressure of the multi-layer winding drum are large, and the disorderly rope phenomenon is easy to occur. Therefore, the wire rope with a diameter slightly smaller than the pitch of the rope groove and the diameter of the rope groove should be selected to add the touch area between the wire rope and the drum.

With the rapid development of market economy, all walks of life are improving the production process and quality of products, galvanized iron wire industry can not be an exception, of course. However, as a result of galvanized iron wire types differ, its characteristics and production process is also different. Galvanized wire selection of high quality low carbon steel rod processing, is the selection of high quality low carbon steel.

5, when limited by the terrain, the barbed rope barbed rope protective net before and after the continuous setting, take the place as the end of the barbed rope protective net, and deal with the end of the sealing.

Post time: 02-02-23

Hot dip galvanizing is dipped in zinc liquid melted by heating, with fast production speed and thick but uneven coating. The market allows a low thickness of 45 microns and a high of more than 300 microns. The color is dark, the consumption of zinc metal is much, the formation of infiltration layer with the matrix metal, the corrosion resistance is good, and the outdoor environment of hot dip galvanized can be maintained for decades. Application range of hot dip galvanizing: because the coating is thicker, hot dip galvanizing has better protective performance than electric galvanizing, so it is an important protective coating for iron and steel parts in harsh working environment. Hot-dip galvanized products are widely used in chemical equipment, petroleum processing, Marine exploration, metal structure, power transmission, shipbuilding and other industries, in the field of agriculture such as sprinkler irrigation, greenhouse and construction industry such as water and gas transmission, wire casing, scaffolding, Bridges, highway guardrail and other aspects, has been widely used.

The characteristics of hexagonal wire mesh: strong structure, flat surface, with good corrosion resistance, oxidation resistance and so on.

Blade barbed rope is a new product of safety protection supplies, and other barbed rope is different with very sharp blade, its production process is the stainless steel sheet stamping forming. The blade barbed wire protective net is a new kind of protective net. The blade barbed wire produced by our factory is made of corrosion-resistant hot-dip galvanized steel plate or stainless steel plate.

Hot dip galvanizing is a kind of external treatment technology in the production of fasteners. The common varieties of hot dip galvanizing fasteners are electric galvanizing, powder galvanizing, mechanical galvanizing and hot dip galvanizing. Wire factory according to different requirements of customers for fasteners, different hot-dip galvanized surface treatment. Galvanized layer and steel is a metallurgical connection, become a part of the steel surface, so the durability of the coating is more reliable.

Annealed wire is mainly through low carbon steel heating, hot drawing, constant temperature and other processes made into soft iron wire, because in the use of different, so there are different in the production process, made of a variety of specifications. Annealed wire can be widely used, mainly because annealed wire and other kinds of iron wire, has many advantages.

5, according to the wire diameter thickness to adjust zinc dipping time

Post time: 04-04-23

(2) Spray large number hook mesh guardrail should be used electric spray paint or electrostatic spray paint.

Four: spray blade thorn rope long service life.

Now most people buy barbed rope choose blade barbed rope, why is this? The blade gill net is made of hot-dip galvanized steel plate or stainless steel sheet to punch out sharp knife sheets. The high tension galvanized steel wire or blade barbed wire is made of stainless steel wire as the core wire. Because the gill net shape is not easy to contact, so it can reach excellent protection barrier effect. The primary raw materials of the product are galvanized sheet and stainless steel plate.

The cooling circulation system uses spray to cool the drawing die, and takes away a lot of heat generated by the drawing machine in high speed drawing in time to ensure the quality of the wire. Control drawing process parameters: drawing speed 10 ~ 12m/s; Winding tension 8 ~ 10N; Measuring length 30km; The mass fraction of lubricant is 3.5 ~ 4.5%; pH value of lubricant 7 ~ 8; Lubricant temperature 30 ~ 40℃.

Pressure welded steel grid plate is the steel grid plate fixed by pressure resistance welding at each intersection of bearing flat steel and transverse bar, which is called pressure welded steel grid plate. Torsion torsion square steel is generally used for cross bar of pressure welded steel grid. Although they do not belong to the same variety, but in the steel lattice plate standards and performance are still the same.