ZJ Composites sectional steel water tanks

Cold galvanizing, also called electric galvanizing, is the use of electrolytic equipment to remove oil, pickling, after the pipe fitting into the composition of zinc salt solution, and connected to the negative electrode of the electrolytic equipment. Wire factory on the opposite side of the pipe fittings placed zinc plate, connected to the positive electrode of the electrolytic equipment is connected to the power supply, the use of current from the positive electrode to the negative electrode will deposit a layer of zinc on the pipe fittings, cold plating pipe fittings is first processed after galvanized.

In the calculation process of 12*14 specifications of barbed rope, it can not be calculated according to the above calculation formula, because first of all, two specifications of raw materials are used, the thinner the wire diameter, the higher the processing cost. Generally speaking, a kilogram of 12*14 barbed rope can reach about 7.5 meters, and the ratio of warp wire to barbed rope cannot be calculated according to the traditional ratio of 7 to 3. The exact amount of stinging and use the warp need to increase after a series of professional measurement on the loss of raw materials and so on factors to calculate.

The drawing process of the product drawing process has a great influence on the product function. Generally, a large total surface reduction rate of about 90% (see area reduction rate) and a small pass surface reduction rate (about less than 23%) are selected to ensure the endurance of the product. On the high strength spring steel wire, drawing should control the exit temperature of each passage of the steel wire is lower than 150℃, to avoid the steel wire due to strain aging and appear to change the crack, which is the formation of steel wire scrap the primary disadvantage.

First, the tensile strength is durable

Hot dip galvanizing, also known as hot dip galvanizing, is a method of obtaining a metal covering layer by immersing a steel member into a molten zinc solution. With the rapid development of high-voltage power transmission, transportation and communication, the protection requirements for steel parts are becoming higher and higher, and the demand for hot-dip galvanizing is also increasing. Usually the thickness of electrogalvanized layer is 5 ~ 15μm, and the large roll galvanized wire layer is generally more than 35μm, or even up to 200μm. Hot dip galvanized coating ability is good, dense coating, no organic inclusions.

1. High tensile strength and durability

Breeding cattle and sheep with thorn rope effect is still better, because the advantages of thorn rope are more. So is the effect of thorn rope used for livestock breeding good?

Three is to do a good job in the production of galvanized wire products clean and tidy, in accordance with the scientific method of operation to operate the production, the operator should wear the required dress. If it is hot dip galvanized wire products, we must do a good job of passivation, will be able to effectively prevent discoloration, prolong the method of discoloration, can solve the problem of discoloration.

Common galvanized iron wire equipment is usually used in barbecue net, barbecue net generally requires to have a long service life, with galvanized iron wire equipment to wire a layer of zinc, barbecue net is not easy to be corroded.

Pet cage is generally made of high quality iron wire, low carbon steel wire, stainless steel wire welding, its characteristics are beautiful, light, folding, easy to store. Pet cage surface treatment is generally: cold galvanizing, hot galvanizing, spraying, dipping, chrome plating, nickel plating and other methods. Pet cage is mainly used for family breeding pets and protection.

Post time: 27-04-22

Mainly suitable for flat welding.

③ Galvanized iron wire shall not be damaged when it is tightened.

The production and processing process of blade barbed rope is tedious, which requires the cooperation of all departments, and the production cycle is relatively long. The barbed rope, whether galvanized barbed rope or stainless steel barbed rope, due to the relatively simple structure, the degree of mechanization in the production process is relatively high, so this is also a big difference in the price.

The quality of hot-dip galvanized barbed wire is only good in the surface of the wire attached to the galvanized layer, and with the chemical reaction, the surface of the zinc layer will gradually lose effect because of the oxidation reaction, this situation is more prominent in the humid area of the environment. And because after all, it is rusty iron wire, so the quality of hot-dip galvanized barbed rope is certainly not up to the level of stainless steel barbed rope.

The screen is made into a box-like container, with stone filled with cages, can be used to protect and support seawall, hillside, road and bridge, reservoir and other civil engineering, flood control and flood resistance is a good material.

4, galvanized can be used zincate galvanized or chloride galvanized process, should use appropriate additives to meet the requirements of this standard coating.

3, PVC plastic coated barbed rope protection function is very good

Many people do not know how to choose high quality cut wire, I will give you a detailed introduction. The raw material of cutting wire is divided into: stainless steel cutting wire, copper cutting wire, steel wire cutting wire, copper plated steel wire cutting wire, galvanized steel wire cutting wire, iron wire cutting wire, aluminum wire cutting wire and so on.

More network is the application of the stone cage net, stone cage net because it is used in water conservancy engineering more, so the anticorrosion performance requirements for wire is relatively high, so the general use of zinc aluminum alloy wire or high galvanized wire. Common wire diameter has 2.0mm, 2.2mm, 2.5,mm, 2.7mm and so on.

Hot – plated wire average performance: reflected in its cross – section, longitudinal uniformity. In the actual process of operation, such as steel wire jitter, the surface scum plating pot and other reasons will cause the surface of galvanized wire galvanized layer accumulation, should strive to solve the problem. In addition to these reasons, we should pay attention to the tooling and process must be stable, and regular testing should be done to ensure the uniformity of the galvanized layer.